12 Results
12.1 Scenario outline
12.1.1 Simulation Summary
The simulation summary (left of Figure 242) provides a quick access to the mean, median and stand...
12.1.2 Simulation status
The progress bar (right of Figure 242) reflects the percentage of events simulated with respect t...
12.1.3 Generic system outline
During the event generation all involved transceivers (ILT, ILR, VLR and VLT) are plotted in grap...
12.1.4 Cellular system outline
Once SEAMCAT has determined the number of UEs per cell either through simulation of optimal capac...
12.2 Overview of output results
Table 51: Interference criteria summary for various victim systems Victim system Intere...
12.3 Generic model Results
Introduction
After running a simulation with generic system, each of these signals is displayed with indicated...
12.3.1 Generated signals results
dRSS folder (ANNEX 4:) with dRSS vector; iRSS unwanted folder (ANNEX 5:) with as many iRSSu...
12.3.2 Calculated radius
The calculated radius folder contains the values of the coverage and/or simulation radii calculat...
12.3.3 Intermodulation results
iRSS intermodulation folder (Figure 248) with as many iRSSintermod vector for each combinatory co...
12.3.4 Overloading results
As a result of the equation described in Annex A5.4, for each event and at each frequency, the su...
12.4 Spectrum sensing results
Introduction
When the cognitive radio mode is activated, SEAMCAT resturns the output vector shown in Figure 25...
12.4.1 sRSS vector
The sRSS vector (dBm) is merely the sRSS value calculated at the selected WSD frequency (i.e. whe...
12.4.2 WSD frequency
This vector represents the actual selected frequency (MHz) at which the WSDs are allowed to trans...
12.4.3 WSD e.i.r.p.
The actual selected e.i.r.p. (dBm) at which the WSDs are allowed to transmit as the result of the...
12.4.4 Victim frequency vector
The victim frequency vector (MHz) represents the frequency at which the victim device transmits p...
12.4.5 Average e.i.r.p. per frequency
It presents the average e.i.r.p. per event (dBm vs MHz) for all the active WSDs transmitting at a...
12.4.6 Average active WSDs per frequency vector
It provides the average number of active WSD per event for a specific frequency: ...
12.5 CDMA output results
12.5.1 CDMA capacity finding
During the pre-simulation part, the system estimates the load of the network as shown in Figure 2...
12.5.2 CDMA results
Once SEAMCAT has completed the simulation, the results are shown as displayed in Figure 261, when...
12.5.3 CDMA results for cell selection algorithm
When the CDMA “cell selection” algorithm is simulated, the following output vectors are also avai...
12.6 OFDMA output results
The results of the OFDMA simulation are given in terms throughput loss of the OFDMA victim. Figur...
12.7 EPP results
In case an EPP is used and it returns a set of result, they will also be included next to the sta...
12.8 Cellular Structure
Introduction
When simulating CDMA or OFDMA systems, you will have access to the additional tab "Cellular struc...
12.8.1 Plot configuration
The top part of the detailed system information screen contains a range of checkboxes used to con...
12.8.2 Summary of event #n
The “Summary of event#n” panel provide a few metrics on the number of users simulated Figure 268 ...
12.8.3 Inspect selected element
12.8.3.1 Detail When an element of the main plot is selected, i...
12.9 Interference calculations
12.9.1 Introduction
The Interference Calculation Engine (ICE) is that part of the SEAMCAT architecture which calculat...
12.9.2 Interference calculation GUI
When the simulation is finished, the dRSS and the iRSS vectors are stored. You may proceed to use...
12.9.3 Interference Calculation Engine Control
It allows to the calculation of the probability of interference for several ICE configurations (...